|
|
Регистрация | Пригласить друга | Все альбомы | Файловый архив | Справка | Сообщество | Календарь | Сообщения за день | Поиск |
|
Опции темы |
04.07.2022, 17:11 | #1 |
Местный
Регистрация: 28.06.2009
Адрес: Новгородская обл.
Сообщений: 1,657
Репутация: 115
|
Xerox DC700 ошибка 077-123
|
04.07.2022, 20:20 | #2 |
Местный
Регистрация: 04.02.2010
Адрес: Нск
Сообщений: 3,128
Репутация: 374
|
Re: Xerox DC700 ошибка 077-123
077-123 Paper does not actuate the registration sensor in the specified time after the registration clutch in energized in duplex mode.
ИМХО не хватает прижима на тонкой бумаге ( и как следствие - на более высокой скорости) попробуйте на роликах перед узлом регистрации подсунуть под пружинки ... скрепку, зубочистку - чуть усилить прижим кстати - непонятно - проблема для всех лотков? - и где именно заминает? Последний раз редактировалось dastin; 04.07.2022 в 20:23.. |
05.07.2022, 12:28 | #3 | |
Местный
Регистрация: 28.06.2009
Адрес: Новгородская обл.
Сообщений: 1,657
Репутация: 115
|
Re: Xerox DC700 ошибка 077-123
Цитата:
Заминает со всех лотков. Выглядит так: отправляем А3 дуплексом, останов, один лист висит справа под дверцей, которая под выходным лотком, второй лист (точнее это уже вторая сторона первого листа) гармошкой в регистрации. |
|
12.07.2022, 10:39 | #4 |
Местный
Регистрация: 24.09.2008
Адрес: Нижневартовск
Сообщений: 180
Репутация: 12
|
Re: Xerox DC700 ошибка 077-123
Regi In Sensor is not turned On after paper is fed from Duplex.
Датчик регистрации входа не включается после подачи бумаги из режима двусторонней печати. Check the following: Registration Transport and/or Duplex Transport failure due to Roll wear/deterioration Registration Transport and/or Duplex Transport failure due to foreign substance in Paper Path Pre Regi Roll for dirt/paper particles/wear/a poor rotation Drive gears for wear/breakage Drawer Connectors contact points for foreign objects/bent pins/burnout Go the the LED (On PWBs) Status Information RAP. Replace PH Driver PWB ( PL 11.3), IOT Drive PWB ( PL 11.1) and the MCU PWB ( PL 11.1) one at a time in the order shown |
12.07.2022, 10:40 | #5 |
Местный
Регистрация: 24.09.2008
Адрес: Нижневартовск
Сообщений: 180
Репутация: 12
|
Re: Xerox DC700 ошибка 077-123
Execute UI Diagnostics [077-007 Reg. Motor: 430mm/s]. There is operation noise from the Reg. Motor. Yes No Unanswered Check the wire-wound resistance of Reg. Motor is approx. 0.8 Ohms at the measurement points below. P/J271-2 to pins 1/3 P/J271-5 to pins 4/6 If OK, go to CH8.9 Registration Drive and troubleshoot the Reg. Motor circuit. Execute UI Diagnostics [077-102 Reg. Sensor]. Place paper in front of the Reg. Sensor. The display changes. Yes No Unanswered Go to CH8.10 Registration and check the following for an open wire, short or poor contact: Reg Sensor P/J 118-2 to IOT Drive PWB P431-A7 Reg Sensor P/J 118-1 to IOT Drive PWB P431-A10 Reg Sensor P/J 118-3 to IOT Drive PWB P431-A8 If OK, replace the Reg. Sensor ( PL 4.4) before replacing the IOT Drive PWB ( PL 11.1). Execute UI Diagnostics [077-017 Pre Reg. Motor: 640mm/s]. There is operation noise from the Pre Regi Motor. Yes No Unanswered Check the wire-wound resistance of Pre Reg. Motor is approximately. 0.8 Ohms at the measurement points below. P/J270-2 to pins 1/3 P/J270-5 to pins 4/6 If OK, go to CH8.9 Registration Drive and troubleshoot the Pre Reg. Motor circuit. |
22.12.2022, 22:05 | #6 |
Новичок
Регистрация: 20.09.2011
Адрес: Вологда
Сообщений: 9
Репутация: 0
|
Re: Xerox DC700 ошибка 077-123
Xerox 700, та же ошибка (077-123) при тех же обстоятельствах.
Интересует - решилась ли проблема, и каким образом? |
|
"Форум индустрии цифровой печати" 2008-2023 Все вопросы по сотрудничеству: Электропочта: info@trade-print.ru Москва, Печатников пер. |