XEROX DocuColor DC 12 номера ошибок и описание поломок - Страница 3 - Цифровая печать как бизнес - форум и портал
Индустрия цифровой печати - отраслевой портал  

Вернуться   Цифровая печать как бизнес - форум и портал > Технический раздел - ремонт принтеров, копиров > XEROX

Реклама на форуме
  • Дополнительный доход для сервисного инженера. Узнать как…
Ответ
 
Опции темы
Старый 14.10.2008, 10:13   #1
Михаил
Администратор
 
Аватар для Михаил
 
Регистрация: 19.06.2008
Адрес: Александров
Сообщений: 6,215
Вопрос XEROX DocuColor DC 12 номера ошибок и описание поломок

Introducing: The Xerox DC12 style machines.
(Docucolor 12 (DC12) & Docucolor 50 (DC50 or DCCS50)) Overview and Status Codes...
All accounts of the Xerox Docucolor 12 which I’ve heard so far, seem to consider this a superb piece of equipment. It’s a full color copier and printer capable of producing color prints and copies which are truly impressive. There are quite a few of these machines out there… we’ll start with a quick overview and then plunge into the rather deep pool of Status Codes (actually, we’ll just wade a little… the complete listing would take up way too many pages).
The DC12 and the DCCS50 are covered together in one service manual so they are very closely related. These machines are said to run well so long as regular maintenance is observed… one of the most sensitive parts of the machine lies in the Fuser’s Oil application system. Problems in copy quality which may at first appear to be caused by other things can wind up being in the fuser oiler section. Its important to understand the way the machine works a little bit… there is an “IBT” belt which is a transfer belt… this belt gets written on by laser and then developed by each of the colors individually… it keeps going around till each color is overlayed to form the image, then the image is developed onto the Drum from the IBT belt to finally be transferred onto the Paper. With all the layering, it is understandable how crucial a roll the fuser plays in this system. It must have the right temperature, lubrication and pressure to do its job. The Fuser is different from many of the black and white copiers / printers which I know in that it has three Fuser Rollers (the Heat Roll, the Pressure Roll, and the External Roll). It has heater lamps in all three of these rollers as well as thermal fuses. It also has thermistors for heat control and overheat on all 3 rollers (for a grand total of 6 thermistors and 3 thermal fuses / thermostats if you’re keeping count).
There is a way to enter into the Diagnostic Mode from the Control Console or User Interface (UI) although access is somewhat limited. Ideally, you’d be equipped with a PWS (Portable Work Station) which is a laptop computer loaded with software to interface with the machine. From a PWS you’d have a menu driven way of accessing the diagnostics. From the Control Console, you’ll need to get a listing of the codes… there’s no approaching this one blind. You’ll also have to pay extremely close attention to make sure you enter the code you really intend to since the display will give you little to go on. While there are plenty of regular maintenance work and mechanical repair work which any competent tech can handle, it’ll be important to recognize when you’re in over your head… basically, take on the problems which make sense to you and know when to run! If you run into logic problems, you’ll need to get in an expert for sure… let the customer know that you can repair some of the basic and more common problems which occur (such as replacing fuser parts, feed components, etc.) but that you have limited access to information and in some cases, they may need to find someone who is trained on the machine (someone who owns a PWS would be best). If you make friends with someone who knows these machines, keep their number handy.
Like many of the more complex Xerox machines, this one is a bit logic-heavy… so there are more codes than we’ll actually list here, but at least this will give you a good idea which way to look when you get a status code.
Below are the basic layout of the meanings behind the Status Codes:
STATUS CODES:
1-300 Front Door Interlock is open.
1-304 Left Cover Interlock is open.
2-310 User Interface (UI) Panel failure.
2-340 UI RAM failure.
3-xxx Codes are all Communication and memory failures
4-001 Main Motor problem.
4-002 Drum Motor problem.
5-xxx Codes are all Document Feeder (DADF) problems…below are a few you’ll want to know:
5-110 to 5-113 DADF Registration jams.
5-115 to 5-116 DADF Exit jams.
5-196 Document sensed at Document Sensor at power on or when the DADF Top Cover was closed.
5-197 Document sensed at Registration Sensor at power on or when the DADF Top Cover was closed.
5-198 Document sensed at Exit Sensor at power on or when the DADF Top Cover was closed.
5-199 Document duplex sensor jam.
5-301 DADF Top Cover is open.
6-xxx Codes relate to the optics… below are a few select ones:
6-360 Carriage Position Failure.
6-371 Exposure Lamp failure.
6-389 Carriage overrun at scan end.
6-390 Carriage overrun at home end.
7-xxx Codes relate to the Paper Supply…some of the simpler ones are below:
7-281 Tray 1 Lift Motor failure.
7-282 Tray 2 Lift Motor failure.
7-283 Tray 3 Lift Motor failure.
7-284 Tray 4 Lift Motor failure.
7-286/287 Tray 5 Lift Motor problems.
8-xxx Codes are Paper Feed and Registration problems
9-xxx Codes are all Xerographic problems such as toner problems, developer problems, Drum Cartridge problems, ADC (Auto Density Control) problems too. Some examples:
9-271 Yellow Toner empty.
9-272 Magenta Toner empty.
9-273 Cyan Toner empty
9-274 Black Toner empty.
9-311 Wrong Drum Cartridge.
9-372 No Drum Cartridge sensed.
9-374 No Waste Bottle sensed.
9-376 Waste Bottle full.
9-378 Drum Cartridge count expired (40K).
10-xxx Codes are Fuser problems and Paper Exit problems.
10-102 to 10-117 Fuser area paper jams.
10-127 to 10-163 Duplex jams.
10-300 Inverter Cover is open.
10-341 Fuser Oil bottle is empty (30-40K expected yield if the oiler system including the metering blade, donor roll, etc are in good working order). This code should reset automatically when a new Oil Bottle is installed.
10-342 Fuser Web Cartridge needs changing (this code should reset automatically when a new Web Cartridge is installed).
10-359 Open Heat Roll Control Thermistor (the one closer to the middle of the roll).
10-360 Open Heat Roll Overheat Thermistor.
10-361 to 10-365 : Heat Roll not hot enough.
10-366* to 10-367*: Heat Roll Over-temperature.
10-368 Open Press Roll Control Thermistor (the one closer to the middle of the roll).
10-369 Open Press Roll Overheat Thermistor.
10-370 to 10-374: Press Roll not hot enough.
10-375* to 10-376*: Press Roll Over-temperature
10-377 to 10-378: Open External thermistor failures.
10-379 to 10-385 External Heat Roll not hot enough.
10-386* to 10-387*: External Heat Roll Over-temperature
11-xxx Codes are all Sorter related stuff…
14-xxx Codes are ROS (Raster Output Scanner or Laser Module) failures.
15-xxx Codes have to do Image Processing System (IPS) failures in the logic / communications.
16-xxx Codes generally point to network faults.
21-504 Code indicates a problem with an Accessory device such as a Coin Kit.
* Overheat codes must be reset from Diagnostics (NVM adjustments) by entering code 777-160 and changing the value to a ‘0’ after repairs are complete. To get to the NVM adjustments, you’ll need to turn on the power, then while holding down the ‘0’ button, press ‘Start’. The screen will prompt you for an “Access Number”… use the keypad to enter ‘6789’.
Next month we’ll cover how to access the Diagnostics available from the Control Console. You’re going to need a listing of some of the basic Memory Adjustment Codes. This machine requires that you know the code you want to enter… there’s no friendly menus like some of the other Xerox machines we’ve covered here in the past (the 5340 style and the DC220 style for example are menu driven, so you can find your way around intuitively… not so for the DC12). I’ll also have to get you an abbreviated list of the Component Control Codes for testing sensors, motors, etc. I think that’ll do it for this month… hopefully this little taste has piqued your interest without being too much of a tease. See you next month.


ARTICLE # 2: Diagnostic procedures... Introducing: The Xerox DC12 style machines (Part 2) (Docucolor 12 (DC12) & Docucolor 50 (DC50 or DCCS50)) Overview and Diagnostic Codes...
Last month found us wading into the rather deep pool of Status Codes for the Docucolor12 & DCCS50 machines… Just enough to wet your appetite. This is the first series of machines which I’ve dealt with which is a full color machine… it’s a good place to start as its an excellent piece of equipment… well built… just about everyone who has anything to say about it raves about it. So lets continue dreaming in full color…
This month, as promised, we’ll have a peek at some of the Memory Adjustments and Component Test Codes which you’re most likely to need. You will need to keep a list of the codes on hand because the Memory adjustments and Component Tests do not have an intuitive, menu driven diagnostic screen… you cant scroll through a list of possible codes… you simply have to know exactly which code you want to run. There are a few adjustments and tests which are available only if you have a specially equipped laptop computer or “PWS” (Portable Workstation). Fortunately, a vast majority of the diagnostic functions are available from the User Interface (UI) Diagnostics Mode.
Entering Diagnostic Mode: First of all… to enter the User Interface (UI) Diagnostic Mode: Turn on the power… then while holding down the ‘0’ button, press ‘Start’. The screen will prompt you for an “Access Number”… use the keypad to enter ‘6789’ which is the Default Access Number. This should bring you to a menu of options to choose from:

NVM Reset (Non Volatile Memory) / NVM Initialization
NVM Read / Write (memory adjustments)
Component Control (for testing sensors, motors, etc.)
Print (for running Test Patterns from Diagnostics)
Subsystem Check (for fuser nip measurement check out, and developer unit check out)
Max Setup (for setting up copy quality)
We’ll start with the NVM Read / Write (Non Volatile Memory Adjustments)… Again, you need to have the exact code you wish to enter … don’t guess at this or you can screw things up pretty easily. Here’s an abbreviated list:

NVM Code Description Default value Range
700-116 Lighter – Darker Default 0 0-7
700-117 Hue Control Default 0 0-5
700-118 Chroma Control Default 0 0-5
700-119 Sharpness Default 0 0-5
710-004 Document Feeder Lead Edge Registration (simplex)
710-007 Document Feeder Lead Edge Registration (duplex)
715-023 Doc Feeder Side Registration offset 32 0-100
715-132 Scanner Lead Edge Registration correction 50 0-75
715-133 Scanner Lead to Trail Magnification correction 50 44-56
720-001 Side Edge Registration Adjustment (A side) 525 1-16383
720-002 Side Edge Registration Adjustment (B side) 525 1-16383
720-018 Lead Edge Erase (top edge) 35(2.96mm) 0-255
720-019 Trail Edge Erase (bottom edge) 35 0-255
720-020 Side Edge Erase 70 0-255
760-004 Tray 1 Paper Size 3(8.5x11) 0-3
772-018 Fuser Fan Failure Reset (For Resetting 10-398 & 10-399 Status Codes) 1 (set to ‘0’ to clear codes)
774-056 Read CRU Type (Copy Cartridge type) 48 = Metered Version (uses 13R557)
49 = Sold Version (uses 13R558)
777-051 Oil Pump On Time (adjusts oil dispensing) 3000 (ms) 40-10000
777-077 Web Status (0=Full, 1=Near Empty, 2=Empty) 0 (Used to Reset 10-422 Status Code if web cartridge fails to reset it automatically)
777-160 Fuser Failure Status (0=No Problems, 1= Heat Roll Lamp Failed, 2=Heat Roll Safety failure, 3=Press Roll Lamp failed, 4=Press Roll Safety failure, 5=External Roll Lamp failed, 6=Ext. Roll Safety failure. 0 (Used to Reset the following Fuser Fault Codes: 10-366, 10-367, 10-375, 10-376, 10-386, 10-387)
You’ll notice that several of the NVM codes above allow you to reset the machine when certain otherwise unclearable Fault Codes occur. In each case, you’d want to reset the value to ‘0’ to make the Fault Code go away.
Next, you’ll want to be equipped with a list of the more commonly needed Component Control Codes… similar to the NVM codes, you need to know the exact code you want to run. Again, you’ll need to be very careful inputting the codes so that you don’t create unexpected problems for yourself by running the wrong component. First we have a partial list of the Input Codes (these test the sensors and switches):
INPUT COMPONENT TEST CODES:
Input Code Description Status Meaning
001-300 Front Door Interlock Switch High = Open
001-304 Left Cover Interlock Switch High = Open
005-102 Document Present Sensor High = No Document
005-110 Doument Registration Sensor High = No Document
005-115 Document Exit Sensor High = No Document
005-119 Document Duplex Sensor High = No Document
005-300 Platen Switch High = Open
005-301 Top Cover Interlock Switch High = Open
006-212 Scan Registration Sensor High = Light Blocked
007-100 High Capacity Feeder (HCF) Feed Sensor High = Paper Detected
007-186 HCF Stack Height Sensor High = Stack not Home
007-187 HCF Paper Size Sensor High = 8.5x11
007-188 HCF Paper Empty Sensor High = Paper Detected
007-189 HCF Tray Closed Interlock High = Closed
007-308 HCF Docking Interlock Switch High = Docked
008-104 #1 Pre Feed Sensor High = No Paper Sensed
008-105 #1 Feed Out Sensor High = No Paper Sensed
008-109 #2 Pre Feed Sensor High = No Paper Sensed
008-110 #2 Feed Out Sensor High = No Paper Sensed
008-114 #3 Prefeed Sensor High = No Paper Sensed
008-115 #3 Feed Out Sensor High = No Paper Sensed
008-119 #4 Pre Feed Sensor High = No Paper Sensed
008-120 #4 Feed Out Sensor High = No Paper Sensed
008-135 Tray 5 Feed Sensor High = Paper Sensed
008-150 Takeaway Sensor High = No Paper Sensed
008-153 Pre Registration Sensor High = No Paper Sensed
008-155 Registration Sensor High = No Paper Sensed
008-163 Behind Registration Jam Sensor High = No Paper Sensed
008-305 Tray 5 (Bypass) Interlock Switch High = Feeder Open
009-216 IBT Belt Cleaner Retract Home Postion Sensor High = Home Detected
009-217 Oil Roll Retract Home Position Sensor High = Light Blocked
009-220 Developer Rotary Home Position Sensor High = Light Blocked
009-237 Developer Rotary Lock Mechanism Sensor High = Latched
009-249 Waste Bottle Position Sensor High = Set
009-250 Waste Bottle Full Sensor High = Full
009-251 Trickle Bottle Sensor High = Full
009-255 Low Toner Sensor (Black) High = Toner Sensed
009-257 Low Toner Sensor (Yellow) High = Toner Sensed
009-258 Low Toner Sensor (Magenta) High = Toner Sensed
009-259 Low Toner Sensor (Cyan) High = Toner Sensed
010-100 Fuser Entrance Sensor High = No Paper Sensed
010-105 Fuser Exit Sensor High = No Paper Sensed
010-110 Machine Exit Sensor High = No Paper Sensed
010-115 Exit Path Sensor High = Paper Sensed
010-125 Inverter Path Sensor High = Paper Sensed
010-130 Duplex In Sensor High = Paper Sensed
010-132 Duplex Path 1 Sensor High = Paper Sensed
010-133 Duplex Out Sensor High = Paper Sensed
010-220 Press Roll Retract Sensor High = Retract position
010-221 External Heat Roll Retract Sensor High = Retract position
010-222 Oil Sensor High = Oil Empty
Here’s a list of some of the Output Component Codes you’re likely to want to be able to run:
OUTPUT COMPONENT TEST CODES:
Output Code Description
003-002 K1 Relay (from AC Drive PWBA)
004-007 Main Motor
004-009 Fuser Motor
004-021 Drum Motor (Photoreceptor and IBT Belt both come on)
005-011 Doc Feeder (DADF) Set Gate Solenoid Open
005-012 DADF Set Gate Solenoid Close
005-040 DADF Feed Motor
005-055 DADF Document Transport Belt Motor Forward
005-056 DADF Document Transport Belt Motor Reverse
005-075 DADF Registration Gate Solenoid
005-081 DADF Exit Motor
005-084 DADF LED
006-002 Exposure Lamp
006-005 Exposure Cooling Fan (low speed)
006-006 Exposure Scan Motor (scan forward)
006-013 Exposure Cooling Fan (high speed)
007-078 High Capacity Feeder (HCF) Feed Clutch
007-079 HCF Elevator Motor
007-080 HCF Feed Motor
008-006 Tray 1 Nudger Roll Solenoid
008-007 Tray 1 Feed Motor (reverse)
008-008 Tray 1 Feed Motor (forward)
008-009 Tray 1 Takeaway Feed Clutch
008-011 Tray 2 Nudger Roll Solenoid
008-012 Tray 2 Feed Motor (reverse)
008-013 Tray 2 Feed Motor (forward)
008-014 Tray 2 Takeaway Feed Clutch
008-016 Tray 3 Nudger Roller Solenoid
008-017 Tray 3 Feed Motor (reverse)
008-018 Tray 3 Feed Motor (forward)
008-019 Tray 3 Takeaway Feed Clutch
008-021 Tray 4 Nudger Roller Solenoid
008-022 Tray 4 Feed Motor (reverse)
008-023 Tray 4 Feed Motor (forward)
008-024 Tray 4 Takeaway Feed Clutch
008-025 Takeaway Motor
008-030 Tray 5 Nudger Roll Solenoid
008-037 Tray 5 Feed Clutch
008-040 Tray 5 Lift Motor
008-043 Main Motor 2
008-054 Registration Motor
009-011 Cartridge Motor (Black)
009-012 Cartridge Motor (Yellow)
009-013 Cartridge Motor (Magenta)
009-014 Cartridge Motor (Cyan)
009-018 Rotary Lock Mechanism Latch
009-021 Developer Motor Clutch
009-025 IBT Roll Contact
009-026 IBT Roll Retract
009-031 Dispense Motor (Black)
009-032 Dispense Motor (Yellow)
009-033 Dispense Motor (Magenta)
009-034 Dispense Motor (Cyan)
009-040 ADC LED (Auto Density Control)
009-050 Erase Lamp
009-066 IBT Cleaner Contact
009-067 IBT Cleaner Retract
009-068 Pre Clean Corotron
009-085 Rotory Motor Fan
009-088 Blower
009-089 Copy Cartridge Fan
010-004 Fuser Fan (low speed)
010-005 Inverter Gate Solenoid (Invert)
010-006 Inverter Gate Solenoid (Exit)
010-018 Fuser Fan (high speed)
010-020 Inverter Motor (forward / upward)
010-021 Inverter Motor (reverse / down)
010-023 Pressure Roll Contact
010-024 Pressure Roll Retract
010-025 Inverter Roll Nip Solenoid
10-026 Inverter Roll Release Solenoid
010-027 External Heat Roll Contact
010-028 External Heat Roll Retract
10-029 External Heat Roll Lamp
10-030 Heat Roll Lamp
010-031 Pressure Roll Lamp
010-032 Web Motor
010-033 Oil Pump
010-040 Exit Motor
010-047 1st Belt Transfer Roll (BTR)
010-050 Duplex Out Motor
010-060 Fuser Intake Fan (low speed)
10-061 Fuser Intake Fan (high speed)
Михаил вне форума   Ответить с цитированием
Старый 23.09.2009, 18:32   #41
Hell Horseman
Местный
 
Аватар для Hell Horseman
 
Регистрация: 13.05.2009
Адрес: Ростов-на-Дону
Сообщений: 1,273
Репутация: 274
По умолчанию

Цитата:
Сообщение от ЦифраМиг Посмотреть сообщение
Hell Horseman, какое пиво - Блю лейбл ))))
http://forum.trade-print.ru/xerox/33...i-dc-12-a.html
ага, я вот тут на Джеймесона намекнул - так Юлии и след простыл
Hell Horseman вне форума   Ответить с цитированием
Старый 24.09.2009, 14:07   #42
Nipper007
Новичок
 
Регистрация: 18.09.2009
Адрес: Казань
Сообщений: 13
Репутация: 0
По умолчанию


Взамен блю лэйбла

))))
Nipper007 вне форума   Ответить с цитированием
Старый 24.09.2009, 14:47   #43
Hell Horseman
Местный
 
Аватар для Hell Horseman
 
Регистрация: 13.05.2009
Адрес: Ростов-на-Дону
Сообщений: 1,273
Репутация: 274
По умолчанию

Nipper007, ага, смайлов вот мне и не хватало... Эх, пойду кофе с коньячком выпью...
Hell Horseman вне форума   Ответить с цитированием
Старый 23.10.2009, 18:57   #44
ev-d77
Новичок
 
Регистрация: 23.10.2009
Адрес: Новокузнецк
Сообщений: 2
Репутация: 0
По умолчанию

Подсажите, что за ошибка 3-380? Как это лечится?
ev-d77 вне форума   Ответить с цитированием
Старый 23.10.2009, 22:38   #45
ЦифраМиг
Profi
 
Регистрация: 24.06.2008
Адрес: Москва
Сообщений: 7,214
Репутация: 1049
Отправить сообщение для ЦифраМиг с помощью ICQ
По умолчанию

Вроде датчики на ремне перноса загрязнились надо почистить.
ЦифраМиг вне форума   Ответить с цитированием
Старый 27.10.2009, 09:13   #46
ЦифраМиг
Profi
 
Регистрация: 24.06.2008
Адрес: Москва
Сообщений: 7,214
Репутация: 1049
Отправить сообщение для ЦифраМиг с помощью ICQ
По умолчанию

В общем встрял с ошибкой, она несколько раз выскакивала. Суть следующая - печатаем тираж, лист на выходе останавливается наполовину в печке, наполовину уже вышел (или 30% в печке остается).Достаем лист и печатаем дальше, следующий лист тточто так же. Открываем смотрим что там, визуально все в порядке, запускаем тираж дальше. Идет печать листов 30-50 и опять ступор.садимся и помогаем руками вытаскивать листы (тираж же сдавать надо срочно ) смотрим - опять выталкиваются как надо. Потом рррррраз и выходит лист с незакрепленным изображением, печка не пропекает лист, а скорее всего просто валы не сжимаются. Начинаем доставать лист, а на экране уже висит ошибка 10-389, типа прижимной вал не опускается...В общем по совету Михаила, попробовал почистить муфточку на выходе которая (открываем дверцу выходную и снимаем ее). Помогло на какое то время, заодно снял печку и протер все места, где по идее было проскальзываение из-за скопившегося масла и смазки.Все в куче помогла на пару дней. Сегодня опять тоже самое происходит, несмотря на то, что муфту опять разбирал и протирал. Грешу на печку, но что там может быть-шестерня, моторчик???
ЦифраМиг вне форума   Ответить с цитированием
Старый 27.10.2009, 10:27   #47
Михаил
Администратор
 
Аватар для Михаил
 
Регистрация: 19.06.2008
Адрес: Александров
Сообщений: 6,215
По умолчанию

Вообще странно что тонер не закрепился, это значит что нижний вал не подошел, странно как то...
Михаил вне форума   Ответить с цитированием
Старый 16.11.2009, 08:31   #48
ZU2
Новичок
 
Регистрация: 16.11.2009
Адрес: Орск
Сообщений: 6
Репутация: 0
По умолчанию

Цитата:
Сообщение от ЦифраМиг Посмотреть сообщение
Потом рррррраз и выходит лист с незакрепленным изображением, печка не пропекает лист, а скорее всего просто валы не сжимаются. Начинаем доставать лист, а на экране уже висит ошибка 10-389, типа прижимной вал не опускается...
ЦифраМиг, эт fuser drive..у меня такая же беда.тольк я не знаю как поменять эту муфту..может кто нибудь объяснить как её менять? очень-очень надо
ZU2 вне форума   Ответить с цитированием
Старый 16.11.2009, 09:25   #49
ЦифраМиг
Profi
 
Регистрация: 24.06.2008
Адрес: Москва
Сообщений: 7,214
Репутация: 1049
Отправить сообщение для ЦифраМиг с помощью ICQ
По умолчанию

ZU2, уже поменяли ее Надо снять заднюю стенку, снять блок плат и этот двигатель будет распологаться как раз за блоком плат. Из себя представляетдвигатель закрепленный на плате.Достается-крепится легко.Главное найти его.Я ставил сам по консультации по телефону от сервисника.
__________________
Купила мама konica (c)
ЦифраМиг вне форума   Ответить с цитированием
Старый 17.11.2009, 09:55   #50
ZU2
Новичок
 
Регистрация: 16.11.2009
Адрес: Орск
Сообщений: 6
Репутация: 0
По умолчанию

ЦифраМиг, ещё вопрос,верхнюю заднюю крышку надо снимать или нижнюю, и если верхнюю,то надо ли снимать воздушную систему после блока плат?
ZU2 вне форума   Ответить с цитированием
Старый 17.11.2009, 10:30   #51
Михаил
Администратор
 
Аватар для Михаил
 
Регистрация: 19.06.2008
Адрес: Александров
Сообщений: 6,215
По умолчанию

Кстати рекомендую во время разбора самому фоткать или на видео снимать...
Михаил вне форума   Ответить с цитированием
Старый 17.11.2009, 11:26   #52
Александр Аксенов
Местный
 
Аватар для Александр Аксенов
 
Регистрация: 24.06.2008
Адрес: Воронеж
Сообщений: 1,578
Репутация: 147
Отправить сообщение для Александр Аксенов с помощью ICQ
По умолчанию

Воздушную систему всю снимать нестоит там одной секции (та которая около exit motor) достаточно, да, еще придется снять секцию с озоновым фильтром.
Александр Аксенов вне форума   Ответить с цитированием
Старый 17.11.2009, 11:56   #53
ЦифраМиг
Profi
 
Регистрация: 24.06.2008
Адрес: Москва
Сообщений: 7,214
Репутация: 1049
Отправить сообщение для ЦифраМиг с помощью ICQ
По умолчанию

ZU2, надо снимать верхнюю крышку, потом блок плат - он как бы откинется перпендикулярно аппарату.И за ним как раз будет двигатель.
__________________
Купила мама konica (c)
ЦифраМиг вне форума   Ответить с цитированием
Старый 17.11.2009, 14:09   #54
ZU2
Новичок
 
Регистрация: 16.11.2009
Адрес: Орск
Сообщений: 6
Репутация: 0
По умолчанию

Александр Аксенов, муфта находится ниже exit motor`a или правее?
ЦифраМиг, так не этот же двигатель менять надо..
мля,я всё никак не могу найти..эт ппц какой то.
ZU2 вне форума   Ответить с цитированием
Старый 17.11.2009, 14:27   #55
Александр Аксенов
Местный
 
Аватар для Александр Аксенов
 
Регистрация: 24.06.2008
Адрес: Воронеж
Сообщений: 1,578
Репутация: 147
Отправить сообщение для Александр Аксенов с помощью ICQ
По умолчанию

Вытаскиваешь мотор, дальше снимешь дверцу.................. щас сфоткаю))))
Александр Аксенов вне форума   Ответить с цитированием
Старый 17.11.2009, 14:31   #56
Александр Аксенов
Местный
 
Аватар для Александр Аксенов
 
Регистрация: 24.06.2008
Адрес: Воронеж
Сообщений: 1,578
Репутация: 147
Отправить сообщение для Александр Аксенов с помощью ICQ
По умолчанию

Второй этап со стороны выходного лотка.
Фото019.jpg
Снимем дверцу (сначала пластмасску, потом дверцу с петель(никак не прикручена, осторожно провода), потом дуплекс(не четырех винтах))

Фото018.jpg
Когда снимешь дуплекс, там будет планка на фотке приблизительно расположения обвел, держится на двух винтах и еще на одном со стороны exit мотора + там же два стопорных кольца.

з.ы. муфту можно разобрать и промыть WD-40, т.к. жду уже вторую неделю пришлось поэксперементировать на досуге, вращаться стала лучше, вал не падает вообще.

Последний раз редактировалось Александр Аксенов; 17.11.2009 в 14:39..
Александр Аксенов вне форума   Ответить с цитированием
Старый 17.11.2009, 14:51   #57
ZU2
Новичок
 
Регистрация: 16.11.2009
Адрес: Орск
Сообщений: 6
Репутация: 0
По умолчанию


мы говорим об этой муфте?
ZU2 вне форума   Ответить с цитированием
Старый 17.11.2009, 14:55   #58
Александр Аксенов
Местный
 
Аватар для Александр Аксенов
 
Регистрация: 24.06.2008
Адрес: Воронеж
Сообщений: 1,578
Репутация: 147
Отправить сообщение для Александр Аксенов с помощью ICQ
По умолчанию

Да, она, если чистить, бронзовые шайбочки снимаются.
Александр Аксенов вне форума   Ответить с цитированием
Старый 17.11.2009, 15:02   #59
ZU2
Новичок
 
Регистрация: 16.11.2009
Адрес: Орск
Сообщений: 6
Репутация: 0
По умолчанию

Александр Аксенов, спасибо) сейчас буду делать,тольк шурупы все найду,которые в дусю упали)
ZU2 вне форума   Ответить с цитированием
Старый 06.02.2010, 16:12   #60
Lesnik
Местный
 
Аватар для Lesnik
 
Регистрация: 11.03.2009
Адрес: Омск
Сообщений: 128
Репутация: 4
Отправить сообщение для Lesnik с помощью ICQ
По умолчанию

Ребята, помогите ошибка 9-345, знаю что не подходит ракель к ленте переноса, а как это исправить не знаю, чиска не помогает
Lesnik вне форума   Ответить с цитированием
Ответ

Опции темы

Быстрый переход

183 204 195 210 237 243 263 7 8 152 15 16 13 11 10 14 35 9 256 123 37 144 145 146 179 20 258 21 22 124 23 24 97 127 128 25 26 126 136 154 64 65 254 233 159 162 163 164 66 27 98 48 56 120 58 59 60 61 62 135 63 165 166 200 201 202 51 53 167 169 168 172 52 55 54 125 255 207 217 218 219 220 221 222 223 224


"Форум индустрии цифровой печати" 2008-2023

Все вопросы по сотрудничеству:

Электропочта: info@trade-print.ru

Москва, Печатников пер.

Текущее время: 23:41. Часовой пояс GMT +4.

Яндекс.Метрика